You are here: Home » Blog » What Is a Water-Side Economizer in Data Center Cooling?

What Is a Water-Side Economizer in Data Center Cooling?

Views: 0     Author: Site Editor     Publish Time: 2026-11-20      Origin: Site

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
sharethis sharing button

A water-side economizer is a cooling system arrangement that uses favorable outdoor conditions to reduce or eliminate the need for mechanical refrigeration.

In a conventional chilled-water data center, a water-side economizer commonly uses a cooling tower and a liquid-to-liquid heat exchanger to cool the chilled-water circuit without relying entirely on the chiller compressor.

When outdoor conditions are sufficiently favorable, the economizer may provide the required cooling duty. Under intermediate conditions, it may precool returning water while a chiller supplies the remaining cooling.

However, free cooling does not mean zero electricity consumption. Cooling tower fans, pumps, controls, and other auxiliary equipment still require power.

For data center engineers and equipment buyers, the important questions are when water-side economizing is technically feasible, how much mechanical cooling it can replace, and what equipment and operating data are needed to evaluate the complete system.

1. What Is a Water-Side Economizer?

A water-side economizer (WSE), sometimes called a waterside or fluid economizer, uses an external heat rejection source to cool a circulating liquid when environmental conditions permit.

Rather than transferring all the cooling load through a vapor-compression refrigeration cycle, the system uses the available temperature difference between the facility cooling water and the heat rejection circuit.

1.1 The Conventional Cooling Tower Arrangement

In a common water-cooled chiller plant, a cooling tower rejects heat from the condenser-water circuit to outdoor air through evaporative cooling.

When the outdoor wet-bulb temperature is sufficiently low, the tower can produce cooling water suitable for use by an economizer heat exchanger.

A simplified heat rejection path is:

Data Center Cooling Load → Chilled-Water Return → Economizer Heat Exchanger → Cooling Tower Circuit → Outdoor Air

The heat exchanger transfers heat from the building's chilled-water circuit into the tower-water circuit without intentionally mixing the fluids.

1.2 What Makes the Economizer Different from a Chiller?

A conventional chiller uses a refrigeration compressor and associated components to remove heat from the chilled-water circuit.

A water-side economizer uses a liquid-to-liquid heat exchanger and available heat rejection capacity to reduce the required compressor operation.

The economizer does not create cooling independently of outdoor conditions.

Its available capacity depends on water temperatures, flow rates, equipment performance, and environmental conditions.

1.3 Is a Water-Side Economizer the Same as an Air-Side Economizer?

No.

An air-side economizer uses favorable outdoor air conditions to reduce mechanical cooling of the data center air.

A water-side economizer transfers heat through a liquid circuit and associated heat rejection equipment.

This distinction is important because the water-side arrangement can reduce the need to introduce large quantities of outdoor air directly into the IT environment.

2. Main Components of a Water-Side Economizer System

2.1 Cooling Tower or Other Heat Rejection Equipment

The heat rejection equipment removes heat from the circulating liquid.

In a conventional cooling tower economizer, evaporative cooling allows the tower's leaving-water temperature to approach the outdoor wet-bulb temperature.

Actual performance depends on tower design, airflow, water flow, heat load, and ambient conditions.

Some broader fluid-economizer architectures use dry coolers or closed-circuit fluid coolers. These operate under different physical limitations and should not be assumed equivalent to a conventional open cooling tower arrangement.

2.2 Liquid-to-Liquid Plate Heat Exchanger

A plate heat exchanger is commonly installed between the tower-water circuit and the chilled-water circuit.

Its functions include:

  • Transferring heat between the separate liquid circuits

  • Limiting routine exposure of the closed chilled-water system to tower-water contaminants

  • Accommodating appropriate differences in fluid chemistry

  • Providing a defined thermal separation boundary

The exchanger must be selected for the required heat-transfer duty, operating temperatures, pressure limits, and allowable pressure drops.

Gasketed plate-and-frame heat exchangers are commonly considered for larger serviceable installations, but the appropriate construction depends on the application.

2.3 Pumps, Valves, Sensors, and Controls

A water-side economizer requires more than a heat exchanger.

Depending on the design, its supporting equipment may include:

  • Cooling tower and chilled-water pumps

  • Isolation and bypass valves

  • Temperature and pressure sensors

  • Flow measurement and control devices

  • Strainers or filtration equipment

  • Heat exchanger protection and maintenance provisions

  • Building management system (BMS) interfaces

The piping and control arrangement determines whether economizer and mechanical cooling can operate separately or together.

2.4 How the Economizer Differs from a CDU

A Coolant Distribution Unit (CDU) commonly separates a data center's Facility Water System (FWS) from its Technology Cooling System (TCS).

A water-side economizer is usually part of the facility cooling or heat rejection architecture.

The economizer reduces mechanical cooling demand, while the CDU manages the interface with liquid-cooled IT equipment.

These two functions may exist in the same data center, but they should not be confused.

For further background, see Why Data Centers Separate Facility and IT Cooling Loops.

3. Three Operating Modes of a Water-Side Economizer

A well-designed economizer system may operate in different modes depending on outdoor conditions and cooling demand.

3.1 Full Economizer Mode

Full economizer operation occurs when the external cooling source and heat exchanger can meet the required chilled-water duty without mechanical refrigeration.

Under these conditions, the chiller compressor may be shut down or bypassed according to the approved system design.

The cooling tower, pumps, and controls may continue operating.

Full economizer capability must be verified at the required supply temperature, flow rate, and heat load.

3.2 Partial Economizer Mode

During intermediate outdoor conditions, the economizer may not be able to reach the required chilled-water supply temperature independently.

However, it may still reduce the temperature of the water returning from the data center.

A chiller then supplies the remaining cooling.

This arrangement can reduce mechanical refrigeration duty when properly designed and controlled.

3.3 Mechanical Cooling Mode

When the available external cooling conditions do not provide useful economizer capacity, the system may operate primarily through the chiller.

The economizer can be bypassed or isolated according to the hydraulic arrangement.

The transition must preserve required chilled-water flow, temperature stability, and equipment safety.

3.4 Integrated vs. Non-Integrated Economizer Arrangements

An integrated economizer can operate simultaneously with mechanical cooling.

A common integrated arrangement positions the economizer heat exchanger upstream of the chiller so that the water can be precooled before entering the chiller.

A non-integrated arrangement generally uses either the economizer or the chiller to supply the cooling load rather than operating both simultaneously.

3.4.1 Why Integrated Operation Can Be Useful

Integrated operation can utilize available economizer capacity even when outdoor conditions are not sufficient for full compressor-free cooling.

However, the actual benefit depends on system design, hydraulic configuration, and controls.

Engineering Check: Confirm the Sequence of Operation

Before selecting equipment, request a written sequence explaining:

  • Conditions for starting economizer operation

  • Conditions for full and partial economizer modes

  • Chiller enable and disable logic

  • Valve and pump changeover requirements

  • Minimum flow and temperature restrictions

  • Failure and alarm response

Commissioning Check: Verify the Mode Transitions

The commissioning plan should confirm that the system maintains the required cooling conditions while changing between full economizer, partial economizer, and mechanical cooling modes.

Control behavior must be verified under the applicable operating conditions rather than inferred from a conceptual diagram.

4. What Determines When Water-Side Economizing Is Available?

4.1 Outdoor Wet-Bulb Temperature

For conventional cooling tower economizers, outdoor wet-bulb temperature is a major factor.

Evaporative cooling performance depends on the difference between the tower water temperature and the air's wet-bulb temperature.

The tower cannot be assumed to deliver water at the outdoor wet-bulb temperature itself.

A finite temperature approach is required.

4.2 Cooling Tower Approach Temperature

Cooling tower approach can be expressed as:

Cooling Tower Approach = Tower Leaving-Water Temperature − Outdoor Wet-Bulb Temperature

The approach depends on cooling tower design and the actual operating conditions.

A smaller approach generally requires greater heat rejection capability or different operating conditions.

4.3 Plate Heat Exchanger Approach Temperature

The economizer heat exchanger also requires a temperature difference.

For a typical counterflow arrangement, a cold-end approach can be defined as:

Heat Exchanger Cold-End Approach = Chilled-Water Leaving Temperature − Tower-Water Entering Temperature

This temperature difference influences the minimum chilled-water temperature achievable at the specified operating point.

The heat exchanger selection must also satisfy the required capacity and pressure-drop limits.

4.4 Required Chilled-Water Supply Temperature

The system's required chilled-water temperature strongly affects economizer availability.

If the facility can operate with warmer chilled water, the economizer may provide useful cooling during a wider range of outdoor conditions.

However, the permitted water temperature depends on the data center's air cooling equipment, liquid cooling equipment, and applicable IT thermal requirements.

4.5 Annual Weather and Load Profile

A single winter design point cannot establish annual economizer performance.

Engineers should evaluate hourly or suitably representative weather data together with the expected cooling load and equipment performance.

The number of full and partial economizer hours depends on the specific site and cooling architecture.

5. Illustrative Example: When Can an Economizer Meet the Cooling Load?

The following example explains the temperature relationships. It does not represent Aidear equipment ratings or actual data center operating results.

5.1 Hypothetical Design Conditions

Assume the following design requirements:

Parameter

Illustrative Value

Required chilled-water supply

16°C

Chilled-water return

24°C

Cooling tower approach

4 K

Economizer heat exchanger cold-end approach

3 K

Outdoor wet-bulb temperature, Case A

7°C

Outdoor wet-bulb temperature, Case B

14°C

These approach values are assumptions for illustrating the calculation. Their achievement at the required duty must be confirmed by equipment selection.

5.2 Case A: Conditions Favor Full Economizer Operation

First estimate the tower leaving-water temperature:

Tower Leaving Water = Wet-Bulb Temperature + Tower Approach

Tower Leaving Water = 7 + 4 = 11°C

The illustrative minimum chilled-water leaving temperature based on the assumed cold-end approach is:

11 + 3 = 14°C

Because this is below the required 16°C supply temperature, full economizer operation may be feasible.

Actual full-load capability still depends on heat exchanger performance, flow rates, tower capacity, the hot-end temperature difference, and controls.

5.3 Case B: Partial Economizer Operation May Be Possible

At an outdoor wet-bulb temperature of 14°C:

Tower Leaving Water = 14 + 4 = 18°C

The illustrative cold-end temperature becomes:

18 + 3 = 21°C

This is warmer than the required 16°C supply temperature.

The economizer cannot independently achieve the specified supply temperature under the assumed conditions.

However, it may be able to precool the 24°C returning water, allowing the chiller to provide the remaining cooling.

The actual precooling duty must be calculated rather than assumed.

5.4 Why the Calculation Is Only an Initial Check

The temperature calculations establish preliminary feasibility, not a guaranteed equipment selection.

A detailed evaluation requires:

  • Cooling load

  • Water or glycol properties

  • Flow rates on both sides

  • Cooling tower performance

  • Heat exchanger thermal selection

  • Pressure losses

  • Chiller performance

  • Control requirements

Illustrative Example: The temperatures and approach values are hypothetical and are not manufacturer test results or universal design recommendations.

6. How Much Energy Can a Water-Side Economizer Save?

A water-side economizer can reduce compressor operating hours or mechanical cooling duty when outdoor conditions permit.

However, the energy benefit must be calculated for the actual system.

6.1 Compressor Energy Reduction

In full economizer mode, the chiller compressor may not be required to meet the cooling load.

In partial mode, the chiller may operate at a reduced cooling duty.

The corresponding electrical savings depend on the chiller's part-load performance and operating conditions.

6.2 Fan and Pump Electricity Still Matter

Economizer operation may require cooling tower fan power, circulating pump power, and auxiliary electrical input.

Therefore:

Net Energy Savings = Avoided Mechanical Cooling Energy − Additional Economizer-Related Energy

The calculation must use consistent system boundaries and account for equipment that operates in both cases.

6.3 Water Consumption and Maintenance

Cooling tower economizers commonly rely on evaporative cooling.

Their operating water demand includes evaporation and other losses associated with the tower's water management system.

Water treatment, blowdown, scaling, biological control, and maintenance must be evaluated.

Energy savings do not automatically mean reduced water consumption.

6.4 Evaluate Total Cost of Ownership

In addition to energy consumption, the economic analysis should consider installation costs, heat exchanger maintenance, pumping requirements, water treatment, redundancy, and equipment service life.

No universal payback period or energy-saving percentage should be applied without project-specific evidence.

7. Water-Side Economizer vs. Dry Cooler Free Cooling

A conventional cooling tower economizer and a dry cooler-based free-cooling system can both reduce compressor dependence, but their performance is governed by different environmental conditions.

Selection Factor

Cooling Tower Water-Side Economizer

Conventional Dry Cooler Free Cooling

Heat rejection method

Evaporative cooling

Sensible heat transfer to air

Main ambient reference

Outdoor wet-bulb temperature

Outdoor dry-bulb temperature

Normal evaporative water use

Yes

No, for conventional dry operation

Fluid arrangement

Tower water often separated by a heat exchanger

Closed liquid circuit, with additional separation where needed

Main constraints

Tower approach, water quality, exchanger approach

Dry cooler approach, air temperature, airflow

Maintenance focus

Tower water treatment, fouling, pumps, fans

Coils, fans, fluid protection, pumps

Free-cooling capability

Depends on site wet-bulb conditions and equipment

Depends on site dry-bulb conditions and equipment

Neither option is universally superior.

Water availability, facility temperature requirements, local climate, maintenance capacity, and energy costs influence the preferred solution.

For equipment-specific performance assessment, see Aidear's Dry Cooler Performance Verification Guide.

8. What Changes in a Direct-to-Chip Liquid Cooling Data Center?

Modern data centers may combine liquid-cooled servers with traditional air cooling systems.

These systems do not necessarily require the same cooling-water temperatures.

8.1 Higher Cooling-Water Temperatures May Help

Where IT equipment and CDU specifications permit warmer facility water, the available temperature difference to outdoor conditions may increase.

This can extend the operating range of some economizer arrangements.

However, the actual limits must be confirmed against the IT equipment's coolant temperature, flow, and reliability requirements.

8.2 The CDU Adds Another Thermal Boundary

A liquid-to-liquid CDU commonly transfers heat from the Technology Cooling System to the Facility Water System.

Its required approach temperature must be included in the full temperature schedule.

If another economizer heat exchanger separates the facility system from an outdoor cooling circuit, there may be multiple heat-transfer boundaries.

8.3 Avoid Assuming the Same Loop Serves Every Load

A facility may use separate water temperature levels for direct liquid cooling and air cooling.

The cooling plant architecture must account for the requirements of all loads and the interaction between their control systems.

9. Water-Side Economizer RFQ Checklist for Data Center Buyers

Before requesting equipment quotations, establish the design basis for the complete system.

RFQ Item

Information to Confirm

Application

Data center chilled-water plant or facility liquid cooling

Cooling duty

Normal, peak, and minimum operating loads

Required supply temperature

Chilled-water or FWS supply requirement

Return temperature

Expected return conditions

Site climate

Annual wet-bulb and dry-bulb weather data

Heat rejection equipment

Cooling tower, closed-circuit cooler, or dry cooler

Cooling fluids

Water chemistry, glycol type, concentration

Flow rates

Both sides of the economizer heat exchanger

Exchanger approach

Required at the specified duty

Pressure drop

Maximum permitted on each circuit

Operating modes

Full economizer, partial economizer, mechanical cooling

Controls

Temperature reset, sequencing, valves, pumps, alarms

Reliability

Redundancy, isolation, bypass, failure response

Maintenance

Filtration, water treatment, cleaning, access

Documentation

Thermal selection, P&ID, control sequence, testing requirements

9.1 What to Request from the Heat Exchanger Supplier

For the plate heat exchanger, request:

  • Required and calculated heat-transfer duty

  • Four terminal temperatures

  • Fluid composition and properties

  • Both flow rates

  • Allowable pressure drops

  • Plate and gasket or brazing material specifications

  • Design pressure and temperature

  • Fouling assumptions and maintenance provisions

  • Connection details and overall dimensions

  • Applicable inspection and testing documentation

A nominal kW capacity alone is not enough to verify suitability.

9.2 What to Request from the System Designer

The system designer should provide a complete operating concept showing where the economizer connects to the chilled-water plant, how the chiller is bypassed or operated in series, and how cooling continuity is maintained during mode changes.

10. Frequently Asked Questions

10.1 Does a Water-Side Economizer Eliminate the Need for a Chiller?

Not necessarily.

It may eliminate compressor operation during favorable outdoor conditions, but a chiller or other supplemental cooling source may still be required.

10.2 Does Free Cooling Mean Zero Electricity Consumption?

No.

Cooling tower fans, pumps, valves, and controls still require energy.

The benefit comes from reducing mechanical refrigeration energy relative to the alternative operating mode.

10.3 Is a Plate Heat Exchanger Required?

A separate plate heat exchanger is common in conventional open cooling tower economizer arrangements.

Other approved heat rejection and fluid-cooling configurations may use different forms of heat exchange or integrated equipment.

10.4 Is a Water-Side Economizer Suitable for Every Climate?

No.

Suitability depends on site weather, required water temperature, heat load, and equipment performance.

Annual operating-hour analysis is necessary.

10.5 Can a Water-Side Economizer Work with a CDU?

Yes, if the facility cooling architecture and temperature conditions are compatible.

The economizer and CDU perform different functions and must be evaluated as parts of the overall system.

11. Conclusion: Economizer Performance Depends on the Complete Cooling System

A water-side economizer uses favorable outdoor conditions to reduce the mechanical cooling required by a data center.

In conventional chilled-water systems, cooling towers and liquid-to-liquid heat exchangers commonly provide this function.

Full economizer operation may allow the chiller compressor to stop, while an integrated system can provide partial cooling when mechanical refrigeration is still necessary.

The actual benefit depends on outdoor conditions, required supply temperature, heat exchanger approach, flow rates, pumping and fan energy, and controls.

For engineering and procurement teams, the correct approach is to evaluate the complete cooling architecture and its operating conditions rather than selecting individual equipment only by nominal capacity.

Request a Heat Exchanger or Facility Cooling Equipment Quote from Aidear

Aidear provides plate heat exchanger products and dry cooler products for relevant industrial and facility cooling applications.

If your data center project involves an economizer heat exchanger, outdoor fluid cooling equipment, or a facility-side thermal separation requirement, provide the cooling duty, fluids, temperatures, flow rates, allowable pressure drops, and installation conditions.

Equipment compatibility, performance, and project-specific technical requirements must be confirmed during selection.

Request a Custom Quote to discuss your cooling equipment requirements.

Contact us

Can't Find Ideal Refrigeration System Solutions For Your Industries?

We are an excellent, specialized refrigeration system solutions provider for almost 20 years, our main products are various specifications of heat exchanges, air cooler, condenser and units, which are all covering a wide area of application.
Phone
 
+8613915061591
Address
 
Wujin High and New Technology Development Industry, Changzhou, Jiangsu,China

Products

Services

About Us

Links

© COPYRIGHT 2025 CHANGZHOU AIDEAR REFRIGERATION TECHNOLOGY CO., LTD. ALL RIGHTS RESERVED.