You are here: Home » Blog » Dry Cooler vs Air-Cooled Chiller for Data Center Liquid Cooling: How to Choose

Dry Cooler vs Air-Cooled Chiller for Data Center Liquid Cooling: How to Choose

Views: 90     Author: Site Editor     Publish Time: 2026-11-19      Origin: Site

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
sharethis sharing button

As direct-to-chip liquid cooling becomes increasingly important in AI and high-density data centers, engineers must decide how to reject heat from the facility cooling system.

Two common equipment options are dry coolers and air-cooled chillers. Both transfer heat to outdoor air, but they operate differently and cannot always deliver the same supply-fluid temperatures.

A dry cooler uses fans and an air-to-liquid heat exchanger to reject heat without a refrigeration compressor. An air-cooled chiller uses a mechanical refrigeration cycle to produce chilled liquid, including when outdoor air is too warm for direct dry cooling.

The appropriate choice depends on IT cooling temperature requirements, CDU heat exchanger approach, local climate, load profile, energy consumption, and availability requirements.

This guide explains how to compare these systems and when a combination of both may be preferable.

1. How Dry Coolers and Air-Cooled Chillers Work

1.1 What Is a Dry Cooler?

A dry cooler is a gas-to-liquid heat exchange device, typically consisting of a finned-tube coil, fans, a casing, and associated control systems.

Warm water—or a mixture of water and glycol—flows through the coils, while ambient air passes over the external heat-exchange surfaces.

Heat is transferred from the liquid to the air.

Conventional dry coolers do not utilize a vapor-compression refrigeration cycle.

Consequently, their cooling performance depends largely on the temperature difference between the circulating liquid and the outdoor air.

1.1.1 The Fundamental Temperature Limitation

A conventional sensible dry cooler cannot continuously cool its liquid below the entering outdoor air dry-bulb temperature.

In practical operation, the leaving-fluid temperature must remain above the entering-air temperature by a sufficient approach temperature.

Engineering Check: Dry Cooler Temperature Approach

For a defined operating point:

Dry Cooler Approach = Leaving Fluid Temperature − Entering Air Dry-Bulb Temperature

A smaller approach generally requires more heat-transfer capability and may affect coil size, airflow, fan power, and equipment cost.

Design Review: Confirm the Actual Selection Point

Before accepting a dry cooler proposal, confirm that the supplier has calculated capacity at the specified design ambient temperature, liquid flow rate, fluid composition, and required leaving-fluid temperature.

Do not use a nominal capacity measured at another operating point as proof of performance.

1.2 What Is an Air-Cooled Chiller?

Air-cooled chillers utilize a refrigeration cycle consisting of a compressor, an evaporator, an expansion device, and an air-cooled condenser.

The refrigerant absorbs heat from the circulating coolant within the evaporator and subsequently releases that heat into the ambient outdoor air via the condenser.

Because the refrigeration cycle operates across varying pressure and temperature levels, the chiller is capable—within its specified operating range—of producing coolant at a temperature lower than that of the ambient outdoor air.

However, the compressor and other components consume electrical energy; furthermore, both the actual cooling capacity and the operating efficiency of the unit depend on the specific operating conditions.

1.3 Why They Are Not Interchangeable

A dry cooler directly rejects heat from a liquid circuit to outdoor air.

An air-cooled chiller removes heat from a liquid circuit through a refrigeration cycle before rejecting that heat outdoors.

Both may connect to facility-side cooling infrastructure, but they have different temperature capabilities and control requirements.

2. Dry Cooler vs Air-Cooled Chiller: Technical Comparison

Selection Factor

Dry Cooler

Air-Cooled Chiller

Main operating principle

Sensible air-to-liquid heat exchange

Mechanical refrigeration

Compressor

Not required for conventional dry cooling

Required for conventional vapor-compression cooling

Cooling below ambient air temperature

Not possible for a conventional dry cooler at steady state

Possible within equipment operating limits

Main electrical loads

Fans and associated circulating pumps

Compressors, condenser fans, and associated pumps

Ambient temperature dependence

Directly limits achievable leaving-fluid temperature

Affects available capacity and efficiency

Refrigeration circuit

Not required

Required

Coolant circuit

Water or compatible secondary fluid

Chilled water or compatible secondary fluid

Maintenance focus

Coils, fans, filters where fitted, and hydraulic components

Refrigeration circuit plus fans, controls, and hydraulic components

Potential advantage

Compressor-free heat rejection when conditions permit

Controlled cooling under conditions requiring lower fluid temperatures

Main selection limitation

Temperature approach to ambient air

Energy use, operating envelope, and system complexity

Neither system is automatically the lower-cost choice over its entire operating life.

The comparison must use the same thermal duty, outdoor conditions, redundancy requirements, and system boundaries.

3. Start with the Data Center Liquid Cooling Temperature Requirements

3.1 Understand the FWS and TCS Interface

Many direct-to-chip liquid cooling systems use two circuits:

  • Facility Water System (FWS): Supplies cooling capacity from the facility infrastructure.

  • Technology Cooling System (TCS): Circulates approved coolant through IT equipment.

A Coolant Distribution Unit (CDU) commonly connects the circuits through a liquid-to-liquid heat exchanger.

This allows the fluid quality, pressure, and temperature requirements to be managed separately.

For additional background, see Why Data Centers Separate Facility and IT Cooling Loops.

3.2 Include the CDU Heat Exchanger Approach

The required IT coolant inlet temperature is not necessarily the same as the facility supply temperature.

For a typical cooling arrangement:

Cold-End CDU Approach = TCS Supply Temperature − FWS Supply Temperature

The facility supply temperature must therefore be compatible with the TCS requirement after accounting for the CDU approach and any applicable distribution effects.

3.3 Confirm the IT Equipment Temperature Envelope

Before selecting outdoor cooling equipment, confirm:

  • Minimum and maximum approved TCS inlet temperatures

  • Expected IT return temperature

  • Design and partial-load heat generation

  • Required coolant flow rate

  • Permitted temperature variation

  • Condensation-control requirements

  • CDU operating and control limitations

Do not assume that all AI servers or liquid-cooled racks support the same coolant temperature.

ASHRAE facility-water temperature classes are useful design references, but the actual IT equipment and CDU requirements remain controlling inputs.

4. When Is a Dry Cooler Suitable for Data Center Liquid Cooling?

4.1 Warm-Water Liquid Cooling Applications

Dry cooling solutions become more viable when a facility can operate at higher coolant temperatures.

If a facility allows for a higher fluid supply temperature, a greater temperature differential can be established between the coolant and the ambient outdoor air.

This extends the periods during which dry coolers can meet cooling requirements without the need for compressor operation.

4.2 Climate and Design Ambient Temperature

The selected dry cooler must be capable of meeting the specified heat rejection load under the corresponding outdoor design conditions.

For systems installed in regions with temperate climates, the duration of cooling that can be achieved without the use of a compressor is often longer than that for similar systems installed in hot climates.

However, climatic conditions alone are not sufficient to determine suitability.

The required fluid outlet temperature and the heat exchange temperature difference—also known as the approach temperature—are equally critical.

4.3 Outdoor Airflow and Installation Requirements

Dry cooler performance also depends on airflow.

The engineering review should consider:

  • Fan selection and control

  • Available installation space

  • Air recirculation risk

  • Required maintenance clearance

  • Altitude and air density

  • Noise restrictions

  • Coil fouling and corrosion exposure

  • Freeze protection

A dry cooler that satisfies a catalogue rating may not provide the same capacity if the installation restricts airflow.

5. When Is an Air-Cooled Chiller the Better Choice?

5.1 Lower Required Supply Temperatures

An air-cooled chiller may be necessary when the required facility fluid temperature cannot be achieved by sensible dry cooling at the site's ambient conditions.

This is particularly relevant when the same cooling plant must serve equipment that requires relatively low chilled-water temperatures.

5.2 High Outdoor Temperature Conditions

A chiller can provide mechanical cooling when outdoor air is too warm for direct dry cooling.

However, chiller selection still requires verification of available capacity, electrical input, and operating limits at the specified high ambient temperature.

The nominal capacity alone is not sufficient.

5.3 Mixed IT and Room-Cooling Requirements

A data center may contain both liquid-cooled equipment and traditional air-cooled IT loads.

These applications may have varying requirements regarding cooling temperatures.

While a single low-temperature chilled-water system can accommodate certain mixed-load environments, it may limit the opportunity to leverage "warm-water" cooling—an energy-saving mode that utilizes higher-temperature water.

Consequently, it may be worth evaluating whether to implement a tiered cooling temperature strategy or a hybrid cooling system.

6. Illustrative Example: Compare Cooling Feasibility at Design Ambient

Consider a hypothetical data center liquid cooling system.

The following temperatures are illustrative and do not represent Aidear product performance.

6.1 Define the Required Temperatures

Design Parameter

Illustrative Value

Maximum required TCS supply temperature

35°C

Assumed CDU cold-end approach

3 K

Required FWS supply temperature

32°C

Assumed dry cooler approach

5 K

Outdoor air temperature for matching this condition

27°C

The facility supply requirement is:

35°C − 3 K = 32°C

For the assumed dry cooler approach:

32°C − 5 K = 27°C

6.2 Interpret the Result

Under these assumptions, if the selected dry cooler is capable of achieving an approach temperature of 5 K at the design load, it can deliver an outlet fluid temperature of 32°C when the outdoor air temperature is 27°C.

If the outdoor temperature rises, the dry cooler will no longer be able to maintain an outlet fluid temperature of 32°C while the thermal load remains constant.

In such a scenario, it may be necessary to use a larger dry cooler, implement auxiliary cooling measures, reduce the thermal load, or increase the allowable outlet fluid temperature.

6.3 Why an Air-Cooled Chiller May Be Needed

If the facility must maintain 32°C supply fluid during outdoor conditions at which dry cooling cannot meet the duty, mechanical cooling is one possible solution.

The chiller must still be selected for the required cooling capacity, fluid temperature, ambient operating condition, and allowable power consumption.

6.4 What This Example Does Not Prove

This calculation is a simplified temperature-feasibility illustration.

It does not determine the required heat exchanger area, fan power, compressor power, annual operating cost, or actual free-cooling hours.

Those require project-specific equipment performance data and climate analysis.

7. Why a Hybrid Dry Cooler and Chiller System May Be Preferable

7.1 Free-Cooling Mode

When ambient conditions permit, a dry cooler or appropriate economizer heat exchanger can satisfy the facility cooling requirement without running the chiller compressor.

Fans and pumps still consume electricity.

Therefore, free cooling does not mean zero-energy cooling.

7.2 Mechanical Cooling Mode

When outdoor conditions exceed the dry-cooling capability, a chiller can provide the additional temperature reduction required by the system.

The design must specify whether the chiller supplies the full load or operates with another cooling path.

7.3 Partial Free-Cooling Mode

Some systems use available dry cooling to precool a liquid circuit while the chiller provides the remaining cooling.

This can reduce mechanical cooling duty under suitable conditions.

However, an additional heat exchanger, piping, controls, and pressure losses must be considered.

7.3.1 Mode Changeover Requirements

Mode changes should be based on verified temperatures, flow conditions, cooling capacity, and control logic.

Potential issues include unstable valve operation, insufficient flow, unexpected supply temperature changes, and conflicting pump controls.

Procurement Check: Request the Sequence of Operation

Ask the system designer or supplier to explain the conditions for entering and leaving each cooling mode.

Commissioning Check: Verify All Required Modes

The agreed commissioning plan should establish how free-cooling, partial mechanical cooling, full mechanical cooling, alarm conditions, and failure transitions will be verified.

8. Compare Annual Energy Use, Not Just Nameplate Power

A meaningful energy comparison requires an hourly or suitably representative climate and load assessment.

8.1 Dry Cooler Energy Consumption

Dry coolers consume electrical energy through fans and the associated circulating pumps.

Fan control, liquid flow, equipment size, and ambient conditions affect the required input.

8.2 Chiller Energy Consumption

Air-cooled chillers require compressor and condenser fan power in addition to associated circulation equipment.

Efficiency depends on operating temperatures, load, compressor control, and equipment design.

8.3 Use a Common System Boundary

When comparing alternatives, include the electrical consumption of all equipment relevant to the proposed system:

  • Compressors, where applicable

  • Dry cooler or condenser fans

  • Facility pumps

  • Additional heat exchanger pressure losses

  • Controls and auxiliary components

Annual energy may be estimated using:

Annual Energy = Sum of Operating Power × Operating Hours

Use the correct equipment power for each operating condition rather than one fixed nominal value.

8.4 Evaluate Total Cost of Ownership

In addition to electricity, review:

  • Initial equipment cost

  • Piping and installation

  • Electrical infrastructure

  • Maintenance requirements

  • Space and structural requirements

  • Redundancy equipment

  • Expected replacement and servicing costs

Claims that one option is always cheaper or more efficient should be avoided unless supported by a project-specific comparison.

9. Reliability, Redundancy, and Maintenance Considerations

9.1 Cooling Availability

For a continuously operating data center, the cooling system must be assessed under normal operation, design weather, maintenance conditions, and relevant failure scenarios.

A dry cooler may have fewer major mechanical subsystems than a chiller, but that does not automatically establish higher system availability.

9.2 Redundancy Design

Depending on the project, redundancy may involve additional dry coolers, chillers, pumps, power sources, heat exchangers, or distribution paths.

The redundancy strategy must consider common failures as well as individual equipment failures.

9.3 Maintenance Requirements

Dry coolers require attention to coil cleanliness, fan condition, water-side or glycol-side components, and freeze protection.

Air-cooled chillers additionally require refrigeration-system maintenance, including appropriate refrigerant circuit and compressor-related checks.

Actual maintenance requirements depend on the selected equipment and service environment.

10. Data Center Cooling Equipment Selection Checklist

Before requesting quotations, the buyer should confirm the following information.

Design Item

Information Required

Cooling duty

Normal, peak, and future heat rejection load

IT cooling conditions

Required TCS supply and return temperatures

CDU

Approach temperature, pressure drop, and rated duty

FWS conditions

Required supply and return temperatures

Outdoor climate

Design dry-bulb temperature and annual hourly weather data

Cooling fluid

Composition, glycol concentration, and properties

Flow rate

Required and allowable operating range

Pressure loss

Maximum allowable pressure drop

Capacity verification

Performance at specified ambient and fluid conditions

Annual energy

Fan, pump, compressor, and auxiliary power

Operating strategy

Free cooling, mechanical cooling, and changeover modes

Reliability

Redundancy and fault-response requirements

Installation

Footprint, airflow clearance, noise, and maintenance access

Quality requirements

Test methods, documents, and acceptance criteria

For a dry cooler RFQ, request the detailed thermal selection sheet and stated fan power at the specified operating point.

For an air-cooled chiller RFQ, request the cooling capacity and electrical input at the actual required leaving-fluid temperature and ambient conditions.

11. Frequently Asked Questions

11.1 Can a Dry Cooler Replace an Air-Cooled Chiller?

Sometimes, but only when the required coolant temperature can be maintained by sensible heat rejection under the relevant operating conditions.

A dry cooler cannot be assumed to replace mechanical refrigeration throughout the year.

11.2 Is Dry Cooling Always More Energy-Efficient?

No universal comparison is valid without the operating conditions.

Dry cooling avoids compressor power during suitable conditions, but fan and pump power still matter.

The total system energy must be evaluated.

11.3 Does a Liquid-Cooled Data Center Always Need a Chiller?

No. Some warm-water liquid cooling systems can operate without conventional refrigeration compressors when climate, facility design, and IT temperature requirements permit.

Other installations require mechanical cooling for part or all of the year.

11.4 Can a Dry Cooler Connect Directly to Server Cold Plates?

A dry cooler should not automatically be connected directly to the IT cooling circuit.

Many systems use a CDU to separate the facility and IT loops and manage coolant quality and hydraulic conditions.

Alternative architectures require explicit engineering validation.

11.5 Is an Adiabatic Cooler the Same as a Conventional Dry Cooler?

No. An adiabatic cooler may use water-assisted air cooling to improve heat rejection under certain conditions.

Its performance, water consumption, maintenance, and operating constraints differ from conventional dry operation.

It should be evaluated as a distinct option.

12. Conclusion: Choose the Cooling Architecture Around the Required Temperature

The most important question is not whether a dry cooler or air-cooled chiller is universally better.

It is whether the selected equipment can maintain the required facility cooling conditions under the actual climate, heat load, and operating requirements.

A dry cooler can be attractive for warm-water liquid cooling when outdoor conditions allow compressor-free heat rejection.

An air-cooled chiller may be necessary where the required liquid temperature cannot be maintained through dry cooling alone.

A hybrid system can combine both approaches, subject to appropriate engineering design and controls.

For procurement teams, a sound decision requires comparable thermal selection data, realistic operating conditions, energy calculations, and documented reliability requirements.

Request a Data Center Cooling Equipment Quote from Aidear

Aidear offers dry cooler products and industrial chiller products for relevant heat-transfer and cooling applications.

For a preliminary equipment evaluation, provide the required cooling duty, coolant composition, supply and return temperatures, flow rate, design ambient temperature, installation requirements, and expected operating conditions.

Any project-specific equipment performance, certifications, control functions, and testing requirements should be confirmed during technical quotation review.

Request a Custom Quote to discuss your facility-side cooling requirements.

Contact us

Can't Find Ideal Refrigeration System Solutions For Your Industries?

We are an excellent, specialized refrigeration system solutions provider for almost 20 years, our main products are various specifications of heat exchanges, air cooler, condenser and units, which are all covering a wide area of application.
Phone
 
+8613915061591
Address
 
Wujin High and New Technology Development Industry, Changzhou, Jiangsu,China

Products

Services

About Us

Links

© COPYRIGHT 2025 CHANGZHOU AIDEAR REFRIGERATION TECHNOLOGY CO., LTD. ALL RIGHTS RESERVED.