You are here: Home » Blog » How Supply Water Temperature Changes Data Center Cooling Efficiency

How Supply Water Temperature Changes Data Center Cooling Efficiency

Views: 110     Author: Site Editor     Publish Time: 2026-11-20      Origin: Site

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
sharethis sharing button

Supply water temperature is one of the most important design variables in data center cooling systems. It affects how much energy the cooling plant consumes, when free cooling is available, how heat exchangers are selected, and whether liquid-cooled IT equipment can operate within its approved temperature limits.

For facilities using direct-to-chip liquid cooling, higher supply water temperatures can create opportunities to reduce compressor operation and increase the use of dry coolers or water-side economizers.

However, raising water temperature does not automatically improve total system efficiency. The benefits depend on IT thermal requirements, CDU performance, coolant flow, pumping energy, outdoor conditions, and the overall cooling architecture.

This guide explains how supply water temperature influences data center cooling efficiency and what engineers and equipment buyers should verify before selecting heat exchangers, dry coolers, or chillers.

1. Which Supply Water Temperature Are We Discussing?

Data centers can contain several cooling circuits operating at different temperatures. These temperatures should not be treated as interchangeable.

1.1 Facility Water Supply Temperature (FWS)

The Facility Water System delivers cooling capacity from the building infrastructure to liquid cooling equipment.

Its heat rejection system may include dry coolers, chillers, cooling towers, or other suitable equipment.

In this guide, FWS supply temperature refers to the fluid temperature entering the facility side of the Coolant Distribution Unit (CDU).

1.2 Technology Cooling System Supply Temperature (TCS)

The Technical Cooling System (TCS) delivers coolant from the Cooling Distribution Unit (CDU) to liquid-cooled IT equipment, including server cold plates.

Its supply temperature must meet the equipment manufacturer's requirements.

The CDU typically transfers heat between the TCS and FWS via a liquid-to-liquid heat exchanger while maintaining isolation between the loops.

1.3 Chilled Water Supply Temperature

A separate chilled water circuit may serve Computer Room Air Handlers (CRAHs), other air cooling equipment, or the CDU facility interface.

The chilled water temperature required for room cooling may differ from the temperature suitable for direct-to-chip liquid cooling.

This distinction matters when a data center combines air and liquid cooling.

For an explanation of loop separation, see Why Data Centers Separate Facility and IT Cooling Loops.

2. How Supply Water Temperature Influences Cooling Energy

2.1 Chiller Compressor Energy

Chiller Compressor

In vapor compression chillers, refrigeration energy consumption is partly dependent on the temperature difference between the evaporation and condensation conditions of the refrigeration system.

When the required chilled water temperature increases, a well-designed and properly controlled chiller can operate at a higher evaporation temperature.

Given other relevant conditions being appropriate, this can reduce the required refrigeration temperature rise, thereby improving the chiller's efficiency.

However, the actual reduction in energy consumption depends on compressor characteristics, chiller control, load, condenser conditions, and the equipment's operating range.

There is no universal energy-saving percentage for every 1°C increase in supply water temperature.

2.2 Dry Cooler Heat Rejection

Dry cooler (20).jpg

A conventional dry cooler transfers heat from circulating liquid to outdoor air without a refrigeration compressor.

Its performance depends on the temperature difference between the liquid and the entering air.

For a defined operating point:

Dry Cooler Approach = Leaving Fluid Temperature − Entering Air Dry-Bulb Temperature

If the permissible outlet water temperature increases while outdoor conditions remain constant, the available temperature difference for heat dissipation can be larger.

This can reduce the heat transfer load required per unit area, or allow for different fan operating conditions depending on the choice of cooler.

A higher permissible inlet water temperature can also enable dry cooling even in conditions of higher outdoor temperatures.

2.3 Water-Side Economizer Operation

Water-side energy savers utilize suitable outdoor conditions to reduce or replace mechanical refrigeration.

In cooling tower systems, the available water temperature is affected by the outdoor wet-bulb temperature and the cooling tower performance.

In traditional dry-cooler systems, the relevant environmental reference value is the outdoor dry-bulb temperature.

Increasing the facility's allowable supply water temperature can extend the duration for which the energy saver meets cooling demands.

The actual natural cooling time must be calculated based on local meteorological data, cooling load, equipment performance, and operational control conditions.

2.4 Total Cooling System Efficiency

The complete cooling system includes more than the heat rejection equipment.

Its electrical consumption may include:

  • Chiller compressors

  • Cooling tower or dry cooler fans

  • Facility water pumps

  • TCS circulation pumps

  • Auxiliary controls and equipment

A temperature setting that reduces compressor energy may still require changes in fan speed, flow rate, or pumping power.

The correct objective is to minimize total cooling energy while maintaining acceptable IT temperatures and system reliability.

3. Understanding ASHRAE Liquid Cooling Temperature Classes

ASHRAE TC 9.9 provides liquid cooling environmental classifications for data center equipment.

The W classes describe maximum facility supply liquid temperatures associated with the relevant equipment classes.

ASHRAE Class

Maximum Facility Supply Temperature

W17

17°C

W27

27°C

W32

32°C

W40

40°C

W45

45°C

W+

Above 45°C, subject to the applicable class definition

These classifications do not mean that all servers can operate at every listed temperature.

The actual permitted temperatures must be confirmed with the IT equipment manufacturer and system designer.

3.1 Lower-Temperature Cooling Systems

W17 and W27 applications may be associated with conventional chilled-water infrastructure and economizer operation where suitable.

Mechanical cooling requirements depend on equipment design and site conditions.

3.2 Warm-Water Cooling Systems

Higher facility water temperatures, such as those required for W32 and W40 applications, can expand the range of applications requiring compressor-less cooling.

However, in certain locations or under specific operating conditions, chiller units may still be necessary.

3.3 Why the Highest Temperature Class Is Not Always Best

The maximum water temperature at which a facility can operate is not necessarily the optimal target.

IT cold plate design, processor heat flux, coolant flow rate, thermal resistance, permissible component temperatures, and system operating margins can all limit the permissible supply water temperature.

Temperature ratings should be used as a design reference and cannot replace equipment-specific engineering certifications.

4. The Temperature Chain from IT Equipment to Outdoor Air

To understand overall cooling efficiency, engineers must evaluate the complete temperature chain rather than one supply temperature.

4.1 Starting with the IT Cooling Requirement

The cooling system must ensure that the temperature of critical IT components remains within acceptable limits.

The coolant delivered to the cold plate is only one part of the temperature difference between the processor and the cooling system.

The thermal interface, cold plate performance, coolant properties, and flow rate are equally important.

4.2 The CDU Temperature Difference

A liquid-to-liquid CDU usually transfers heat from warmer TCS coolant to cooler FWS fluid.

For the cooling arrangement used here:

CDU Cold-End Approach = TCS Supply Temperature − FWS Supply Temperature

The required FWS supply temperature can be expressed as:

Required FWS Supply Temperature = Target TCS Supply Temperature − CDU Approach

4.2.1 Why a Smaller CDU Approach Matters

Under specific heat load and flow conditions, a smaller temperature difference in the atmospheric unit (CDU) allows the facility loop to operate at a higher supply water temperature while maintaining the same supply water temperature in the heat exchanger (TCS).

This may increase the opportunity for energy savers to operate.

However, achieving a smaller temperature difference may require increasing the heat exchange area or using a different heat exchanger configuration.

Engineering Check: Exchanger Size and Pressure Drop

A close-approach heat exchanger must be assessed for:

  • Required heat-transfer duty

  • Fluid temperatures on both sides

  • Flow rates and fluid properties

  • Available installation space

  • Allowable pressure drops

  • Material compatibility and fouling considerations

The smallest temperature approach is not necessarily the best economic choice.

Procurement Verification: Compare at the Same Operating Point

Before approving a supplier quotation, require the proposed CDU heat exchanger to meet the specified duty, temperatures, flow rates, and pressure-drop limits simultaneously.

Do not compare nominal temperature approaches quoted at different heat loads.

4.3 Temperature Differences Beyond the CDU

The cooling system may include an additional heat exchanger to isolate the outdoor glycol loop from the indoor freshwater system.

Each thermal boundary introduces an additional temperature difference.

The overall temperature control scheme must account for these effects, as well as the distribution of losses and the required heat margin.

5. How Supply Temperature Interacts with Flow Rate and Pump Energy

Supply temperature is only one part of the cooling calculation.

The required temperature rise through a loop and the coolant flow rate also affect energy use.

5.1 The Basic Heat-Transfer Equation

For a single-phase cooling liquid:

Q = m × Cp × ΔT

Where:

  • Q = Heat-transfer duty (kW)

  • m = Mass flow rate (kg/s)

  • Cp = Specific heat capacity (kJ/kg·K)

  • ΔT = Return temperature minus supply temperature (K)

For the same heat load and fluid properties, a larger temperature difference can reduce the required mass flow rate.

5.2 Why Flow Rate Matters

Flow rate influences pressure drop through piping, valves, cold plates, filters, and heat exchangers.

Pump input can be estimated from:

Pump Power = Volume Flow Rate × Pressure Rise / Pump Efficiency

Use consistent SI units: volume flow in m³/s and pressure rise in Pa gives power in watts.

Reducing flow may reduce pumping energy in a suitable variable-flow system.

However, insufficient flow can increase component temperature, reduce heat-transfer performance, or violate equipment limits.

5.3 Supply Temperature and Temperature Difference Are Not the Same

Increasing the supply water temperature does not automatically reduce the flow rate.

If the supply and return water temperatures rise by the same amount, the temperature difference remains constant.

Under the same heat load and fluid characteristics, the calculated mass flow rate requirement also remains essentially constant.

Therefore, to save flow rate, reasonable adjustments need to be made to the system's temperature difference, hydraulic operating point, or control strategy.

6. Illustrative Example: Comparing Two Facility Water Temperatures

Consider a hypothetical direct-to-chip cooling installation with a CDU and an outdoor heat rejection system.

The example evaluates two temperature schedules at the same heat load.

6.1 Design Assumptions

Parameter

Case A

Case B

Cooling duty

600 kW

600 kW

FWS supply temperature

26°C

30°C

FWS return temperature

31°C

35°C

TCS supply temperature

30°C

34°C

TCS return temperature

35°C

39°C

CDU cold-end approach

4 K

4 K

Temperature rise on each loop

5 K

5 K

Assume the approved maximum TCS supply temperature is 35°C.

Case B remains below that hypothetical limit, while Case A provides a lower supply temperature.

Both schedules are thermodynamically consistent, but actual exchanger performance must be verified.

6.2 Calculate the Required Flow

Assume:

  • Heat load = 600 kW

  • Coolant specific heat capacity = 4.0 kJ/kg·K

  • Temperature rise = 5 K

Then:

m = Q / (Cp × ΔT)

m = 600 / (4.0 × 5)

m = 30 kg/s

Under these assumptions, both cases require approximately 30 kg/s for the specified heat duty and temperature rise.

Raising the supply temperatures alone does not reduce the calculated flow.

6.3 Compare Dry Cooling Feasibility

Assume outdoor air enters a conventional dry cooler at 24°C.

For Case A:

Required dry cooler approach = 26 − 24 = 2 K

For Case B:

Required dry cooler approach = 30 − 24 = 6 K

Case B provides a larger temperature difference between the required leaving fluid and outdoor air.

It may therefore be easier to achieve with a practical dry cooler selection at the specified load.

Case A is more demanding and would require a separate detailed equipment evaluation.

Neither approach represents an actual Aidear cooler rating.

6.4 What Happens During Hot Weather?

If the outdoor air temperature is higher than the facility's required supply air temperature, traditional sensible dry cooling methods cannot maintain that supply air temperature under stable conditions.

In this case, mechanical refrigeration, water-assisted cooling where appropriate, increasing the approved supply air temperature, or other engineering-designed cooling solutions may be necessary.

6.5 What the Example Demonstrates

The example illustrates why warmer supply water can improve heat rejection feasibility without automatically reducing coolant flow.

It does not establish annual energy savings, actual equipment capacity, or a universal temperature setting.

Illustrative Example: All values are hypothetical and are not Aidear test results, verified customer operating data, or equipment performance guarantees.

7. Why Higher Supply Water Temperature Has Limits

7.1 IT Component Thermal Limits

Higher coolant temperatures reduce the available temperature difference between IT components and their cooling fluid.

Where thermal resistance and heat load remain unchanged, component temperatures may rise.

If the cooling system cannot maintain the required thermal conditions, equipment performance and reliability may be affected.

7.2 Cold-Plate and Coolant Requirements

Cold-plate heat-transfer performance depends on the geometry, fluid properties, flow rate, and heat load.

The system must also satisfy coolant quality, materials compatibility, and pressure requirements.

A higher facility water temperature does not remove these constraints.

7.3 Mixed Air and Liquid Cooling

Data centers may use direct liquid cooling for high-power components and air cooling for other equipment.

The cooling water temperature required for air-cooled systems may be lower than that of liquid-cooled loops.

If both systems share a cooling unit, the lower cooling water temperature requirement may limit the runtime of energy-saving devices.

Using a separate temperature loop may be more advantageous, but the resulting additional equipment costs and complexity must be evaluated.

7.4 Condensation and Minimum Temperature

Warmer cooling water can reduce condensation risk, but it does not remove the need for dew-point monitoring.

Supply temperatures must remain within the approved operating range and above any applicable condensation-control threshold.

Both minimum and maximum allowable temperatures belong in the project specification.

8. Supply Water Temperature Reset and Control Strategy

8.1 Why Fixed Temperature Setpoints May Waste Energy

If the facility's water supply temperature is consistently low, the compressor may unnecessarily operate even when the IT cooling system can withstand higher water temperatures.

A well-designed reset strategy can adjust the water supply temperature based on actual heat demand and available cooling conditions.

8.2 Conditions for Raising the Setpoint

A temperature reset strategy may consider:

  • IT equipment coolant temperature limits

  • TCS supply and return temperatures

  • FWS supply and return temperatures

  • Heat load and coolant flow

  • CDU heat exchanger approach

  • Outdoor weather conditions

  • Cooling plant capacity

  • Required reliability margins

The controller should not raise the temperature solely because outdoor conditions become favorable.

It must confirm that the complete cooling system can maintain the required IT operating conditions.

8.3 Coordinating the Cooling Plant and CDU

The plant and CDU control strategies should be coordinated.

For example, the facility plant may adjust supply temperature while the CDU regulates the TCS supply temperature through its permitted control mechanisms.

Poor coordination can cause unstable valves, unnecessary pump operation, or temperature oscillation.

8.4 Commissioning and Failure Response

The operating sequence should define:

  • Setpoint limits

  • Control deadbands and response rates

  • Minimum cooling flow

  • Alarm and protective thresholds

  • Sensor failure behavior

  • Loss-of-cooling response

  • Mode transitions between economizer and mechanical cooling

The control system should be tested under representative operating conditions before acceptance.

9. What Equipment Buyers Should Confirm Before Ordering

The required supply water temperature should appear clearly in equipment specifications and supplier RFQs.

RFQ Item

Information to Confirm

Cooling application

Direct-to-chip, immersion, CRAH, or mixed system

Cooling duty

Normal, minimum, and peak heat load

FWS temperature

Required supply and return temperatures

TCS temperature

Approved supply and expected return temperatures

CDU approach

Required approach at specified operating conditions

Coolant

Fluid type, concentration, and material compatibility

Flow rate

Minimum, normal, and maximum flow

Pressure drop

Allowable pressure drop on each circuit

Outdoor conditions

Design dry-bulb/wet-bulb data as applicable

Heat rejection equipment

Dry cooler, chiller, cooling tower, or hybrid arrangement

Energy performance

Fan, pump, compressor, and auxiliary input

Control requirements

Setpoint reset, operating modes, alarms, and monitoring

Reliability

Redundancy, failure response, and maintenance requirements

Verification

Thermal selection report, approved drawings, and acceptance tests

For dry coolers, request performance data at the actual fluid temperature, coolant composition, flow rate, and design ambient temperature.

For chillers, request cooling capacity and power input at the intended leaving-water temperature and ambient operating conditions.

For CDU heat exchangers, provide the four terminal temperatures, both flow rates, fluid properties, and allowable pressure drops.

10. Frequently Asked Questions

10.1 Does Increasing Supply Water Temperature Always Save Energy?

No.

A higher supply temperature may improve chiller operating conditions and create more free-cooling opportunities, but total energy depends on the complete system.

Pumps, fans, heat exchangers, and IT operating constraints must also be considered.

10.2 What Supply Water Temperature Is Best for Data Center Liquid Cooling?

There is no universal optimum.

The correct setting depends on IT equipment limits, CDU approach, heat load, climate, and facility cooling architecture.

ASHRAE temperature classes are useful references, but the actual equipment specification must determine the allowable range.

10.3 Can Warm-Water Cooling Eliminate the Chiller?

It may allow chiller-free operation under suitable conditions.

However, equipment selection must demonstrate that the required facility supply temperature can be maintained throughout the intended operating conditions.

10.4 Does a Higher Supply Temperature Reduce Pump Energy?

Not automatically.

Pump energy depends on flow rate, pressure loss, and pump efficiency.

A warmer supply temperature alone does not necessarily reduce flow requirements.

10.5 How Does CDU Approach Temperature Affect Efficiency?

A smaller CDU approach can allow warmer FWS supply at the same TCS supply temperature.

This may improve economizer opportunities, but the heat exchanger size, pressure drop, cost, and available space must also be evaluated.

11. Conclusion: Optimize the Complete Temperature Chain

Supply water temperature influences data center cooling efficiency through several connected mechanisms.

Warmer facility water can improve some chiller operating conditions, increase opportunities for compressor-free heat rejection, and expand the practical use of dry coolers or economizers.

However, higher temperatures must remain compatible with IT equipment limits, CDU performance, coolant flow requirements, and the cooling system's reliability objectives.

The most effective engineering approach is to begin with the IT thermal requirements, define the CDU temperature difference, assess the facility cooling temperatures, and evaluate heat rejection performance across the actual annual operating conditions.

The goal is not to maximize supply water temperature at any cost. It is to identify the highest practical temperature range that maintains reliable cooling while minimizing total system energy use.

Request a Data Center Cooling Equipment Quote from Aidear

Aidear offers dry cooler products and industrial chiller products for relevant facility-side cooling applications.

For project evaluation, provide the cooling duty, required supply and return temperatures, coolant composition, flow rate, allowable pressure drop, outdoor design conditions, and installation requirements.

Where a CDU heat exchanger is required, the operating conditions and fluid specifications on both sides should also be confirmed.

Actual equipment performance and project-specific capabilities must be verified during the technical quotation process.

Request a Custom Quote to discuss your data center cooling requirements with Aidear.

Contact us

Can't Find Ideal Refrigeration System Solutions For Your Industries?

We are an excellent, specialized refrigeration system solutions provider for almost 20 years, our main products are various specifications of heat exchanges, air cooler, condenser and units, which are all covering a wide area of application.
Phone
 
+8613915061591
Address
 
Wujin High and New Technology Development Industry, Changzhou, Jiangsu,China

Products

Services

About Us

Links

© COPYRIGHT 2025 CHANGZHOU AIDEAR REFRIGERATION TECHNOLOGY CO., LTD. ALL RIGHTS RESERVED.